Effect of sintering temperature on solidification and migration of non-volatile and volatile heavy metals in glass-ceramic

Using tailings as material to prepare glass-ceramic is an excellent way to achieve the resource utilization of solid waste. However, at present, researches on the solidification and migration of heavy metals are limited. Therefore, in this study, ten groups of samples were prepared by controlling sintering temperatures. The solidification, migration, and leaching behavior of non-volatile and volatile heavy metals were studied. The research showed that, with the increase of temperature, the properties of the samples were improved. Fe participated in the phase transformation and evolved into insoluble iron pyroxenes solid solution, while Pb was homogeneously distributed in the glass matrix of glass-ceramics. The leaching concentrations of Fe and Pb in the glass-ceramics were 0.055 mg/L ～0.087 mg/L and 0.074 mg/L ～0.140 mg/L, which were far below the threshold value. The results showed that heavy metals can be effectively solidified in glass-ceramics and have good environmental benefits.     

Vacancy-engineered V2O5-x films for ultrastable electrochromic applications

In the present study, we prepared vacancy-engineered V₂O_5-x films for electrochromic (EC) applications. To investigate the vacancy effect of V₂O_5-x films with high EC performance capabilities, precursor concentrations of V-based sol solutions were varied at 1 wt%, 5 wt%, and 10 wt%. Among them, V₂O_5-x films with a precursor concentration of 5 wt% (V₂O₅-5wt%) showed superior EC performance outcomes due to the (001)-plane-oriented crystal structure, which provides high electrical conductivity with the oxygen vacancy (V_o). In addition, the gravel-like uniform surface morphology with the optimized film thickness provides a stable electrochemical reaction during the EC measurement. As a result, V₂O₅-5wt% exhibited fast switching speeds (2.1 s for coloration and 3.6 s for bleaching), high transmittance modulation (ΔT) (51.32%), high coloration efficiency (CE) (52.3 cm²/C), and excellent cycle stability (85.85% ΔT retention after 500 cycles). In addition, V₂O₅-5wt% showed energy storage capability of 443.7 F/g at a current density of 2 A/g, thus proving its potential for use in multi-functional applications. Therefore, these results provide valuable insight related to the engineering of vacancies in EC films to achieve high-performance EC devices and additional multi-functional applications.     

Flow modeling of high-viscosity fluids in pipeline infrastructure of oil and gas enterprises

Today, the issues related to solving the problem of finding an effective distribution of oil flows through the system of oil pipelines in order to reduce the total energy consumption are relevant. The solution to this problem is connected with selection of rational pumping modes for various technological sections of oil pipelines using modern methods of mathematical programming or new techniques for improving the energy and transport characteristics of oil.Reducing energy consumption during pumping of crude through oil trunk pipelines can be achieved by various methods. Numerous investigations in this direction are mainly carried out to save energy on separate single-line pipelines. However, due to the development of the network of trunk oil pipelines in the world over the past decades, the issues of energy efficient management of oil flows throughout the entire oil pipeline system of oil and gas enterprises become urgent.This paper analyses parameters for pipeline transport of high-viscosity and heavy oils. The article proposes a method for assessing the rheological properties of oil for further planning of pumping taking into account the preservation of oil quality and an increase in energy and transport characteristics. The proposed solutions and tasks for predicting changes in the viscosity-temperature characteristics of the flow for blends of different oil types are especially relevant in the current conditions of an increase in the share of oil production with complex rheological characteristics. Results of the presented investigations may be used for planning the measures of efficient transportation of high-viscosity and heavy oils.     

Dynamic Oscillation via Negative Differential Resistance in Type III Junction Organic/Two-Dimensional and Oxide/Two-Dimensional Transition Metal Dichalcogenide Diodes

Among many of 2D semiconductor-based devices, type III PN junction diodes are given special attentions due to their unique function, negative differential resistance (NDR). However, it has been found uneasy to achieve well-matched type III PN junctions from 2D–2D van der Waals heterojunctions. Here, the authors present other alternatives of type III heterojunctions, using 2D p-MoTe₂/organic n-type dipyrazino[2,3-f:2′,3′-h]quinoxaline-2,3,6,7,10,11-hexacarbonitrile (HAT-CN) and 2D p-WSe₂/n-MoO_x systems. Those junction diodes appear to well-demonstrate static and dynamic NDR behavior via resonant tunneling and electron–hole recombination. Extended to an inverter circuit, p-MoTe₂/n-HAT-CN diode enables multilevel inverter characteristics as monolithically integrated with p-MoTe₂ channel field effect transistor. The same NDR diode shows dynamic LC oscillation behavior under a constant DC voltage, connected to an external inductor. From p-WSe₂/n-MoO_x oxide diode, similar NDR behavior to those of p-MoTe₂/n-HAT-CN is again observed along with LC oscillations. The authors attribute these visible oscillation results to high peak-to-valley current ratios of their organic or oxide/2D heterojunction diodes.     

Review on development of metal/ceramic interpenetrating phase composites and critical analysis of their properties

Metal/ceramic composites are in high demand in several industries because of their superior thermo-mechanical properties. Among various composite types, the interpenetrating phase composites (IPCs) with percolating metallic and ceramic phases offer manifold benefits, such as a good combination of strength, toughness, and stiffness, very good thermal properties, excellent wear resistance, as well as the flexibility of microstructure and processing route selection, etc. The fabrication of metal/ceramic IPCs typically involves two steps - i) processing of an open porous ceramic body, and ii) infiltration of metallic melt in the pores to fabricate the IPC. Although significant progress has been made in recent years for developing both porous ceramics and melt infiltration methods, to the best of the knowledge of the authors, no review article summarizing all the aspects of processing and properties of IPCs has been published till date. This review article is aimed at filling this gap. Starting with a brief introduction about the current status and applications of IPCs, the various processing routes for fabricating open porous ceramic preforms and melt infiltration techniques have been discussed. Subsequently, the data available for various important physical, mechanical, and thermal properties for IPCs have been critically analyzed to thoroughly understand their dependence on various structural and processing parameters. To compare the properties of IPCs with other relevant materials, seven different Ashby material property maps have been used, and the domains for IPCs have been created in them. For each map, the concept of material indices has been employed to critically discuss how IPCs perform in relation to other material classes for various optimum design conditions. Finally, a detailed future outlook for further research on IPCs has been provided.     

Highly sensitive and wide-range flexible sensor based on hybrid BaWO4@CS nanocomposite

Flexible photoelectronic devices are in demand right now. In this work, a new family of biopolymer-based photodetectors is described. Chitosan (CS) was utilized as a safe, biodegradable host biopolymer, and nanostructured barium tungstate (BaWO₄) particles were used as the nanofiller of the biopolymer matrix to prepare flexible optical sensors. The co-precipitation process was used to produce the filler powders, which were then dried at room temperature without using any surfactants or hazardous solvents. The fabricated sensor showed high flexibility and sensitivity to UV/proton/alpha and laser irradiation. X-ray diffraction (XRD), XPS, FTIR, EDX-map analysis also confirmed the successful synthesis, related chemical binding, and elements in the nanocomposite structure. According to the TEM images, the average particle size of synthesized BaWO₄ NPs was obtained at about 110 nm. A considerable luminescence emission was observed in the constructed sensor's blue/green and ultraviolet spectral regions under various excitation sources. The developed sensor was nontoxic to the cells and provided soft, thin, antibacterial activity, flexible, and comfortable contact with skin, and promising ionizing ray detection applications in flexible optical sensors.     

Rare-earth free sensitizer in NaLuCrF4:Er upconversion material

Upconversion phosphors are known as a material system that can convert near-infrared light into visible/ultraviolet emissions by sequentially absorbing multiple photons. The studies on upconversion materials often use two rare earth (RE) ions as a sensitizer-activator pair. We investigated the influences on luminescence intensity depending on Cr-doping content (x) of hexagonal NaLu_0.98–xCr_xF₄Er_0.02 (x = 0–0.9) upconversion material by substituting Lu³⁺ ions with Cr³⁺in the absence of Gd³⁺. The change in upconversion luminescence intensity appears with saddle-like shape. We suggest that Cr³⁺ ions play the dual role as a constituent in host lattice and a sensitizer in the upconversion process. Optimal conditions for gaining the strongest upconversion emission correspond to x = 0.3–0.5, where there are effective energy transfers between Cr³⁺ and Er³⁺ ions and CrEr dimers. Apart from these values, the emission intensity decreases rapidly which can be ascribed to the absence of multiple-photon absorption for the case of low Cr³⁺ contents, and to the coupling between Cr³⁺ and/or Er³⁺ ions for the case of high Cr³⁺ contents. Magnetization and electron-spin-resonant measurements were performed to understand the correlation between the optical and magnetic properties.     

脉冲激光与电弧布置方式对铝合金焊接熔滴过渡与焊缝形貌的影响

以2219铝合金为基板，研究了不同脉冲激光-电弧布置方式下的熔滴过渡与焊缝形貌特征，分析了熔深增加的机理. 结果表明，当脉冲激光照射母材时，脉冲激光主要提供对母材的热输入，母材温度的增加有助于促进熔滴铺展，稳定熔滴过渡过程；当脉冲激光照射熔滴缩颈时，主要提供对熔滴的力输入，蒸发反力的作用下形成"一脉一滴"，显著提高熔滴过渡频率与熔滴飞行速度，增加了熔滴对熔池的冲击力，熔深增加；当脉冲激光交替的照射熔池和熔滴时，一方面能够对母材进行加热，有助于熔滴的铺展，另一方面能够提高熔滴过渡频率，提高焊缝的均匀性.     

Extraction equilibrium conditions of beryllium and aluminium from a beryl ore for optimal industrial beryllium compound production

This study examines the extraction of beryllium and aluminium from a Nigerian beryl ore using Cyanex®272 in kerosene from an aqueous sulphate pregnant solution. Parameters such as extractant concentration and equilibrium pH that dictates the extraction yield were studied. Under the following conditions: temperature 27?±?2°C, phase ratio 1?1, about 45.50 and 46.76% of beryllium and aluminium were extracted by 0.15?mol?L^?1 Cyanex®272 concentration within 30?min. However, the extraction yield of beryllium and aluminium was increased to 91.68% and 97.89% at equilibrium pH of 3 and 4, respectively, for beryllium and aluminium at 27?±?2°C. A 0.05?mol?L^?1 H₂SO₄ solution was found to be adequate for the stripping of about 99.00% Be and 95.40% Al from the loaded organic phase. The pure solutions containing metal ions were accordingly beneficiated to obtain beryllium and aluminium compounds of industrial values.